![wanderer solar charge controller wanderer solar charge controller](https://cdn.shopify.com/s/files/1/2603/4406/products/81J-IS96IrL_1024x1024@2x.jpg)
- #Wanderer solar charge controller install
- #Wanderer solar charge controller manual
- #Wanderer solar charge controller Bluetooth
Remote Temperature Sensor Port (optional accessory) 6. This can happen when storing a lithium battery pack in a discharged state for any length of time as self-discharge would gradually deplete the remaining charge. The protection circuit of lithium battery will typically turn the battery off and make it unusable if over-discharged. Lithium Battery Activation The Wanderer PWM charge controller has a reactivation feature to awaken a sleeping lithium battery. Boost Charge: When the battery has charged to the Boost voltage set-point, it undergoes an absorption stage which is equivalent to constant voltage regulation to prevent heating and excessive gassing in the battery. It uses 100% of available solar power to recharge the battery and is equivalent to constant current. VOLTAGE NIGHT BULK CHARGE BOOST FLOAT NIGHT TIME Bulk Charge: This algorithm is used for day to day charging. Key Features Optimized for 12 VDC system voltage 30A charging capacity. The controller comes equipped with fully comprehensive self-diagnostics and electronic protection functions to prevent damage from installation mistakes or system faults.
![wanderer solar charge controller wanderer solar charge controller](http://4.imimg.com/data4/BF/WM/MY-3603689/solar-home-lighting-system-500x500.jpg)
Integrating highly efficient PWM charging, the Wanderer increases battery life and improves system performance. General Information The Wanderer is an advanced charge controller for off-grid solar applications and can be used with a 12V battery or battery bank. Table of Contents General Information 04 Optional Components 06 Identification of Parts 07 Installation 07 Mounting Recommendations Operation 10 LED Indicators 10 System Status Troubleshooting 11 Maintenance 12 Fusing 12 Technical Specifications 13 Electrical Specifications 13 Battery Charging Parameters 13 Dimensions 03 07 14 Wear eye protection and have fresh water available in case there is contact with the battery acid. Be careful when working with large lead acid batteries. Be certain there is enough ventilation to release the gases. Explosive battery gases may be present while charging. Use only sealed lead-acid, flooded, gel or lithium batteries which must be deep cycle. The following symbols are used throughout the manual: WARNING CAUTION NOTE Indicates a potentially dangerous condition.īattery Safety Do NOT let the positive (+) and negative (-) terminals of the battery touch each other.
#Wanderer solar charge controller manual
This manual contains important safety, installation, and operating instructions for the charge controller. Working Temperature: -31☏ - 113☏ / -25☌ - 45☌ĭimensions: 4.7 x 3.0 x 1.1 in / 119x75x27.Important Safety Instructions Please save these instructions.
![wanderer solar charge controller wanderer solar charge controller](https://i5.walmartimages.com/asr/473f7c2f-641d-4c1e-9c2c-d8785ac440ca_1.1935700a47fbfecb3dc85cb6c57ed99f.jpeg)
Nominal Voltage: 12V/24V Auto Recognition
#Wanderer solar charge controller Bluetooth
Integrated RS232 port allows communication with BT-1 Bluetooth module and usage of DC Home smartphone app.Capable of charging over-discharged lithium batteries.
#Wanderer solar charge controller install
![wanderer solar charge controller wanderer solar charge controller](https://cdn.shopify.com/s/files/1/2603/4406/products/71D3UruXYVL_1024x1024@2x.jpg)
Simple Install Fully open the hatch (CCW), insert the appropriate wires, and completely close the hatch (CW). THEN secure each cable by rotating the screws clockwise (CW) to the closed position. Make sure to FIRST lower each terminal hatch by screwing the terminals counterclockwise (CCW) to expose the wire terminal hatch to the open position. Wanderer10A|30A Installation Notes The default starting position of the Wanderer controller terminal hatches are closed (in the UP position) that could mistakenly look like an open wire hatch. Designed for off-grid solar applications, this advanced charge controller is compatible with various types of 12V/24V batteries, including Lithium! With a simple interface for ease of use, this controller comes equipped with fully comprehensive self-diagnostics and electronic protection functions to prevent damage from installation mistakes or system faults. The Renogy 10A Wanderer solar charge controller integrates efficient PWM charging to increase battery life and improve system performance.